ASL INTERCOM PS 430 Manual do Utilizador Página 4

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 11
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 3
User Manual PS 430 / Issue 1 © 1994 ASL Intercom, Utrecht, Holland.
4
4.0 FRONT PANEL CONTROLS & CONNECTOR
1 LISTEN LEVEL control knobs 6 SIDETONE HI trimmers
These knobs preset the listen level for each channel These trimmers (one for each channel) control the
separately. rejection in the high frequency range. It compensates
2 TALK buttons
These buttons allow you to talk to each channel microphone (unit feedback).
separately or simultaneously.
Any Talk button activates the gooseneck or headset
microphone, the large green LED at each channel This trimmer allows you to dim the speaker automati-
indicates if the microphone is switched on to that cally, when the gooseneck microphone is switched on.
channel. It prevents:
Latched switching:
When a TALK button is pressed quickly, the
microphone will be switched on, and is electronically
latched. When pressed again, the microphone will be
switched off.
When the microphone is latched on, it can be muted by - switch off TALK buttons.
a mic mute from a PRO Series master station or power - inject an audio signal on the selected intercom
supply. channel.
Momentary switching:
When a TALK button is pressed and held, the
microphone will be switched on, and when released,
will be switched off.
3 CALL buttons
These push buttons activate the call system, for each
channel separately.
A momentary push will send a call signal to all stations
connected to the intercom channel and the call LEDS
will start flashing.
Press and hold the button for 2 seconds will activate
the call buzzer, if not muted.
After the CALL button is released the LEDS will
continue to flash for further 2 seconds.
4 MASTER VOLUME
This knob adjusts the volume of the speaker or
headset.
5 SIDETONE LEVEL trimmers
These trimmers (one for each channel) control the level
of your own voice as you hear it in the speaker or
headset. It prevents the speaker from feeding back into
the gooseneck microphone.
Adjustment procedure for all sidetone trimmers:
- set trimmer in start position : fully clockwise.
- switch off the microphone of all connected
(speaker!) stations.
- switch on the microphone of the PS 430.
- turn up volume.
- speak into the headset microphone.
- adjust the listen level by turning the sidetone
trimmers.
The operating area is between fully clockwise and
minimum level.
Adjusting the sidetone does not affect the level of your
voice as it is heard by other stations.
the capacity of the interconnecting cables. It prevents
the speaker from feeding back into the gooseneck
7 SPEAKER ATTENUATOR trimmer
- unit feedback if sidetone rejection is not sufficient.
- system feedback or a 'hollow' sound when the
gooseneck microphones of other speaker stations
on the same channel are activated simultaneously.
Adjustment procedure :
- turn up volume.
- activate microphone and adjust the desired amount
of attenuation.
The speaker attenuator has no effect when a headset
is used.
8 BUZZER VOLUME trimmer
This trimmer adjusts the volume of the internal buzzer,
which is located behind the front panel. The buzzer is
activated if you press the CALL button of the PS 430 or
a CALL button of any other station (on the channel to
which the PS 430 is connected), longer than 2 seconds
and the buzzers are not muted (on the master station
or power supply).
9 HEADSET connector
A XLR-4 type connector for the connection of a local
headset when private conversation is desired. These
must have a can impedance of 200 ohms (or greater),
or each minimum 400 ohmd when in parallel.
The headset microphone may be of the dynamic or
electret type
Pin assignments :
1. Shield mic. (GND)
2. mic. +
3. phones +
4. phones -
When connecting a headset, speaker and gooseneck
microphone will be disabled automatically.
The PS 430 can optionally be equiped with a XLR-6
headset connector for binaural use.
Jumpers on the front PCB board inside determine the
destination of the listen signals on the headset.
Each listen signal of the four channels can
independantly be placed:
- on the left or right can.
- on both cans.
Vista de página 3
1 2 3 4 5 6 7 8 9 10 11

Comentários a estes Manuais

Sem comentários